• vgbaron replied to the topic Land replacing water in the forum Usability 2 years ago

    Yup! Reran UTX Europe setup and cleared it up.

    Thanx Justin!

    Vic

  • vgbaron started the topic Land replacing water in the forum Usability 2 years ago

    HI Justin – I’m positive this isn’t a Toposim issue but wonder if you have any thoughts. Using P3D4 I was flying around the boot of Italy (LIBC) and I noticed there was land where there should be water. Zooming out in top down view I can see there are numerous land tiles replacing he water tiles all around the boot. Just to be certain, I disabled…[Read more]

  • vgbaron started the topic ATAP BGGH issue in the forum Usability 2 years, 1 month ago

    Justin –

    in P3D4 was having a major elevation issue at BGGH. After a bunch of trial and error I disabled the 4 BGGH files in the ATAP folder and the problem was resolved.

    Vic

  • Hi Justin – Using P3D4 – installed Tongass Fjords scenery into sim. It contains 8 elevation bgl’s. The attached pic shows the water runway at A29 Sitka near PASI. As you can see there is a water wall near the AI Boat. After some trial and error I found if I disabled Toposim North America, the scenery works just fine.

    I know sewveral users who do…[Read more]

  • Hi Justin –

    Will/are Toposim products compatible with P3D 64bit V4 which is due to be released tomorrow?

    Vic

  • Three guesses!! I recall now seeing the effect once before only it said spring, IIRC. Was an orbx migration issue.

    I’m mainly using UTX Landclass and also had SceneryTech enabled. Think I’ll stay with UTX – more accurate and I like the dev, Allen Kreisman, he’s a hard worker like yourself.

    Vic

  • Tracked it down – disabled SceneryTech NA landclass and problem resolved.

    Vic

  • In P3d – go to MMDO (Durango) – go to map view and zoom out – southwest of the airport, in the mountains are several orange markings. Zooming in shows the words FALL as in the attached.

    If I am flying over it in real time I see them and sometimes a texture will fill in over same.

    Any clue what this might be?

    Vic

  • vgbaron replied to the topic Problem with Oceania? in the forum Usability 3 years ago

    Worth a try. Since it only happens there (so far) I didn’t bother but it doesn’t hurt to check.

    DOH! Completely forgot I have a second system set up with P3D – almost identical. SHoyuld check that out and see if I can spot something. Both are on W10.

    Thanx!

    Vic

  • vgbaron replied to the topic Problem with Oceania? in the forum Usability 3 years ago

    Well, no joy but I’m pretty sure something underlying in the default P3D has gotten corrupted. I disabled everything in the scenery lib that was not default and the issue remained. Only seems to happen around Sydney.

    I’m going to leave it as is, I expect there will be a major release from LM within a few months and I plan to do a clean reinstall…[Read more]

  • vgbaron replied to the topic Problem with Oceania? in the forum Usability 3 years ago

    Will do!

    Thanx!

  • vgbaron replied to the topic Problem with Oceania? in the forum Usability 3 years ago

    I have no other Australia or Oceania products. GEXP3D is worldwide so it “should” be just like FTX Global. I do have Global Vector installed along with UTX. Since UTX doesn’t have AUstralia it shouldn’t be an issue. I did disable Toposim Oceania in Scenery Library and it did not change anything so that for sure eliminates Toposim as the…[Read more]

  • vgbaron started the topic Problem with Oceania? in the forum Usability 3 years ago

    The attached image is just north of YSSY. I ‘m puzzled as to whether this is related to my just installing Australia combo pack or something else going on. The blue areas with trees/water eventually become land but very slowly.

    Any thoughts.

    I have Toposim, GEX, UTX and some ORBX areas installed – not Australia though.

    Thanx,

    Vic

  • vgbaron started the topic File size display . . . in the forum Admin NOTAMs 3 years ago

    Suggestion – unless there’s a way that I just missed – it would be nice to know the size of the individual downloads before starting them. Sometimes, when I haven’t much time, I like to d/l a smaller file and save the big ones for when I have more time. The “old” format would list the name of the files and the size in the selection list.

    edit:…[Read more]

  • Suggestion – unless there’s a way that I just missed – it would be nice to know the size of the individual downloads before starting them. Sometimes, when I haven’t much time, I like to d/l a smaller file and save the big ones for when I have more time. The “old” format would list the name of the files and the size in the selection list.

    edit: ok…[Read more]

  • vgbaron replied to the topic Working out the kinks . . . in the forum Admin NOTAMs 3 years ago

    Suggestion – unless there’s a way that I just missed – it would be nice to know the size of the individual downloads before starting them. Sometimes, when I haven’t much time, I like to d/l a smaller file and save the big ones for when I have more time. The “old” format would list the name of the files and the size in the selection list.

    edit: ok…[Read more]

  • vgbaron replied to the topic Working out the kinks . . . in the forum Admin NOTAMs 3 years ago

    Suggestion – unless there’s a way that I just missed – it would be nice to know the size of the individual downloads before starting them. Sometimes, when I haven’t much time, I like to d/l a smaller file and save the big ones for when I have more time. The “old” format would list the name of the files and the size in the selection list.

    Thanx,

    Vic

  • vgbaron replied to the topic Scenery Library in P3d in the forum Installation 3 years ago

    ok. I’m just thinking ahead. The idea that LM has about installing modules – Client, Content, Scenery is to make reinstall relatively painless. ok, I ASSUME your files are added and do not overwrite any files. If that’s the case, then a reinstall of the LM Scenery module would leave the files in place and all user needs to do is clear up the SL…[Read more]

  • vgbaron started the topic Scenery Library in P3d in the forum Installation 3 years ago

    Hi Justin – Hopefully I can explain this properly – trying to wrap my head around the SL ordering, especially as it relates to ATAP’s. As you know, P3D has recommended that 3rd party products be installed outside of the root folder.

    I have an Add On folder where I put scenery, etc. I know I can just install your product in that folder and layer…[Read more]

  • vgbaron started the topic Scenery Library in P3d in the forum Installation 3 years ago

    Hi Justin – Hopefully I can explain this properly – trying to wrap my head around the SL ordering, especially as it relates to ATAP’s. As you know, P3D has recommended that 3rd party products be installed outside of the root folder.

    I have an Add On folder where I put scenery, etc. I know I can just install your product in that folder and layer…[Read more]

  • Load More